The industrial flanged water pressure control valve is a ratio pressure reducing valve for water service, designed to reduce water pressure by using the difference between the effective pressure areas at both ends of the internal piston. It creates a fixed proportional relationship between inlet and outlet pressure, making it suitable for metallurgy, petroleum, hydraulic systems, water pressure testing units, residential water supply and high-rise building water supply systems.
The flanged connection suits rigid industrial pipework and allows the valve to be installed between standard flanges. Available ratios are 2:1, 3:1, 4:1, 3:2 and 5:2, and the valve reduces both dynamic and static pressure — a useful property in industrial systems that alternate between idle and full-flow conditions.
Not every pressure control problem is the same, and the word "control" can mean different things in different systems. This valve controls pressure by maintaining a ratio, not by holding a setpoint. Understanding the difference is the first step in selecting the right device.
|
Control Objective |
Suitable Device |
Behavior |
|
Keep downstream pressure proportional to upstream |
Ratio pressure reducing valve (this valve) |
Outlet tracks inlet at a fixed ratio |
|
Hold a fixed downstream setpoint |
Adjustable pressure reducing valve |
Outlet held at a preset pressure by a spring mechanism |
|
Hold a setpoint in a large or complex system |
Pilot-operated pressure reducing valve |
Outlet controlled by a pilot circuit acting on the main valve |
|
Protect against overpressure |
Opens to relieve excess pressure |
The industrial flanged water pressure control valve is the correct choice when the system requires a predetermined proportional pressure reduction instead of a completely constant downstream pressure. If the plant needs to change the downstream setpoint frequently, an adjustable or pilot-operated valve will be more appropriate.
The valve operates according to the force balance between different effective piston areas, expressed as P1 × S1 = P2 × S2, where P1 and P2 are inlet and outlet pressure and S1 and S2 are the effective pressure areas at both ends of the piston. Because the two areas differ, the inlet and outlet pressures maintain a predetermined proportional relationship, and the outlet pressure changes with the inlet pressure rather than remaining completely constant.
The ratio is determined by the matched internal valve core and cylinder liner. Different component dimensions create different effective pressure areas, allowing the valve to achieve ratios such as 2:1, 3:1, 4:1, 3:2 and 5:2. The ratio is a structural design parameter and cannot be continuously adjusted during operation; changing it requires a corresponding valve core and cylinder liner configuration.
|
Parameter |
Specification |
|
Standard |
GB/T 21386-2008 |
|
Nominal Diameter |
Available DN sizes should be confirmed according to the selected model |
|
Rated Working Pressure |
1.6 MPa |
|
Minimum Opening Pressure |
0.2 MPa for 2:1 / 0.3 MPa for 3:1 |
|
Pressure Ratio |
2:1, 3:1, 4:1, 3:2, 5:2 |
|
Valve Body |
Ductile Iron, Stainless Steel |
|
Medium |
Water |
|
Temperature |
≤80°C |
|
Connection |
Flanged |
The hydraulic performance of the valve is affected by nominal diameter, inlet pressure, pressure ratio, flow rate and pipeline resistance. As flow increases, pressure loss across the valve and pipeline may also change. For accurate engineering selection, the nominal diameter, operating flow rate, inlet pressure range and required outlet pressure should be considered together, and flow-pressure performance data should be based on the selected valve size and actual test conditions.
Typical applications include metallurgy, petroleum-related systems, hydraulic systems, water pressure testing units, residential water supply systems and high-rise buildings. The valve is also used in pressure zoning applications where downstream pressure needs to maintain a proportional relationship with upstream pressure.
The pipeline should be cleaned before installation, and a Y-type filter should be installed upstream to prevent debris from entering the valve. Gate valves or butterfly valves can be installed before and after the valve for easier maintenance. For systems requiring continuous water supply, two valves of the same nominal diameter can be installed in parallel. The small hole on the valve body must not face upward, as water or debris entering the hole may affect valve operation.
Where the controlled water system serves fire protection, the reducing valve is typically coordinated with the fire pump, alarm valve and fire sprinkler network so that downstream components see a pressure within their rating.
FUXEON® has multiple machining and production facilities and can manufacture several thousand pressure reducing valves per month. Each finished valve undergoes a 2.4 MPa pressure test with a 5-minute holding period to check valve strength and sealing performance before delivery. FUXEON® holds GB/T 19001-2016 / ISO 9001:2015, GB/T 24001-2016 / ISO 14001:2015, GB/T 45001-2020 / ISO 45001:2018 and GB/T 27922-2011 certifications, with documents available on the certificate page.
A: This valve maintains a fixed ratio between inlet and outlet pressure, set by the internal piston areas. An adjustable pressure reducing valve holds a preset downstream pressure using a spring mechanism and can be readjusted in service.
A: A pilot-operated valve uses a pilot circuit to control the main valve, which suits large or complex systems but adds components and maintenance. The ratio valve is mechanically simpler, with relatively low maintenance needs and a generally lower initial cost.
A: No. The outlet pressure changes proportionally with the inlet pressure according to the predetermined pressure reduction ratio. It does not remain completely constant.
A: Decide first whether the downstream section must hold a fixed value or track the upstream pressure proportionally. If it must track proportionally, this valve is the correct choice; if a fixed setpoint is needed, choose an adjustable or pilot-operated valve.
A: As general guidance, domestic water supply is generally no more than 3:1, fire protection systems generally no more than 4:1, and domestic hot water generally no more than 2.5:1.
A: No. The ratio is set by the internal valve core and cylinder liner. Changing it requires replacing the corresponding internal components with a configuration that produces the new ratio.
Need help choosing between ratio, adjustable and pilot-operated pressure control?
Factory-direct supply · 2.4 MPa tested · ISO certified manufacturing